Engineering Graphics

Engineering Graphics


    This course covers generic syllabus for Engineering Graphics.


    UNIT I: Scales, Conic sections, Special Curves

    Representative factor, plain scales, diagonal scales, scale of chords. Construction of ellipse, parabola, hyperbola by different methods; Normal and Tangent. Cycloid, Epi-cycloid, Hypo-cycloid, Involutes, Archimedean and logarithmic spirals.

    UNIT II: Projection

    Projection: Types of projection, orthographic projection, first and third angle projection,
    Projection of points and lines: Line inclined to one plane, inclined with both the plane, True Length and True Inclination, Traces of straight lines.

    UNIT III: Projection of planes and solids

    : Projection of Planes like circle and polygons in different positions; Projection of polyhedrons like prisms, pyramids and solids of revolutions like cylinder, cones in different positions.

    UNIT IV: Section of Solids, Development of Surfaces

    Section of right solids by normal and inclined planes; Intersection of cylinders. Parallel line and radial – line method for right solids.

    UNIT V: Isometric Projections & Computer Aided Drafting

    Isometric scale, Isometric axes, Isometric Projection from orthographic drawing. (CAD): Introduction, benefit, software’s basic commands of drafting entities like line, circle, polygon, polyhedron, cylinders; transformations and editing commands like move, rotate, mirror, array; solution of projection problems on CAD.

    Course Curriculum

    Basic: Scales, Conic sections, Special Curves
    Scales 00:06:00
    Types of Scales 00:08:00
    Metric Table 00:10:00
    Various Types Of Scales Used In Practice 00:04:00
    Plain Scales 00:15:00
    Diagonal Scales 00:15:00
    Ellipse 00:07:00
    Ellipse by Concentric Circle Method 00:10:00
    Ellipse by Rectangular Method 00:10:00
    Ellipse by Parallelogram Method 00:10:00
    Ellipse by Arc of Circle Method 00:08:00
    Parabola 00:09:00
    Parabola by Tangent Method 00:08:00
    Hyperbola 00:08:00
    Cycloid 00:08:00
    Involutes 00:09:00
    Spiral 00:08:00
    Projection of Points and Lines
    Projection 00:10:00
    Orthographic Projection 00:10:00
    Question 1 00:10:00
    Question 2 00:10:00
    Question 3 00:10:00
    Projection of Planes and Solids
    Plane 00:05:00
    Traces of Planes 00:05:00
    Solid 00:05:00
    Types of Solid 00:05:00
    Question 1 00:12:00
    Question 2 00:10:00
    Question 3 00:12:00
    Question 4 00:12:00
    Question 5 00:10:00
    Question 6 00:10:00
    Question 7 00:10:00
    Question 8 00:10:00
    Section of Solids & Development of Surfaces
    Section Of Solids 00:10:00
    Development Of Surfaces 00:10:00
    Question 1 00:10:00
    Question 2 00:10:00
    Question 3 00:13:00
    Question 4 00:15:00
    Isometric Projections & Computer Aided Drafting (CAD)
    Computer Aided Drafting 00:10:00
    Benefits Of CAD 00:11:00
    Limitations And Disadvantages OF CAD 00:10:00
    AutoCAD 00:15:00
    Commands used in CAD 00:10:00
    Description Few Commands in CAD 00:07:00

    Course Reviews


    • 5 stars0
    • 4 stars0
    • 3 stars0
    • 2 stars0
    • 1 stars0

    No Reviews found for this course.

    • 224.42
    • 150 Days
    • Course Certificate
    • Wishlist

    Recent Posts

    © Copyright 2013 - 2020 Testclue, All Rights Reserved, Terms and Conditions of use Privacy Policy Could be found here. Refund Policy is available here. Disclaimer : F5, Cisco, VMware, pfsense, VyOS are trademarks and logos of respective companies holding them, Testclue is not official partner or provider of vendor specific courses and material.